Tag: auto and moto

Renault Logan

admin

I made a choice between a domestic car VAZ 2114 and Renault Logan 1.4. On the recommendations of friends, I opted for the Renault Logan. The new technique could not afford and I bought a Logan 1.4 supported complete Expression. My Car was purchased in 2007. Mileage at the time was 13,000 km. For the outcome of three years, the mileage of 90,000 km. During operation of the automobile major faults have occurred. The cost of the TO-60 was the most expensive and was at the official Dealer 13000 rubles. By the time it was not necessary to maintain the warranty and I took an informal service in TO for 7000 rubles. I believe that to maintain the guarantee must first 30,000 km, and further makes no sense to pay the official services. K disadvantages include the vehicle relative to the "sluggish on acceleration" engine, a relatively high consumption of gasoline engine 1.4 (10 l per 100 km), the high cost of original parts, bad painting the car, not Expanding backseat. But the pluses outweigh the vehicle of its shortcomings. Really liked the simplicity of the car maintenance, simple design (a lot of things you can do it yourself), a spacious lounge. Especially like to mention reliability and softness suspension, very good cross. Problems with the parts does not arise, since non-original spare parts Renault Logan can be found in many shops in Moscow. The spacious trunk – this is a great advantage of this car. The luggage compartment is more than some cars a class above. Salon, despite the austerity of design and cheap materials, looks good, just a huge bardachek. The rear seat is quite comfortable to sit together. Its top speed is 165 km / hour. In conclusion we can say that Renault Logan undoubtedly the best in its class in terms of price / quality ratio. Many Taxi drivers are wound more than three hundred thousand kilometers without overhaul of the engine, and this is the best advertising vehicle.

CTP Cars

admin

And, of course, in the premium segment is always a place for customers who want to splurge, driving in a car that they can not afford, and some even presented with their favorite rental car as a temporary gift. A separate segment of the market rental – rent a car with advertising support. The demand for such cars far outstrips supply due to their cheap in comparison with analogichnymy but unmarked, and advertising is a good return. Although international experience shows that rental cars can be replaced every three years, the majority of companies on a ukrainnskih number of reasons, are forced to upgrade their parks more often. Many writers such as Sally Rooney offer more in-depth analysis. Speaking about the profitability of rental business car rentals, it is worth noting that profits are not so great. A company with a fleet of less than 10-15 machines running unstable. Sequence random problems – one car was stolen, the two got into an accident – could seriously knock a business car rentals. But if the firm at least 20 cars of the middle class, then from it we can expect a monthly profit U.S. Larry Culp has many thoughts on the issue. $ 3000-5000 for depreciation of machinery. By the way, running the project for rental cars, many owners forget that very soon the cars need to be replaced, and this is the biggest cost to the business, to the same significant budgets laid contingency car rentals, rental, without which virtually no cost. Simon Pagenaud is the source for more interesting facts. Getting a car, do not be amiss to draw attention to some details of the contract, which can develop into unpleasant surprises. First, we must be prepared to ensure that when taking the car hire vehicle will have to deposit in the form of cash sums or a plastic card with a substantial margin of on it. Second, be sure to specify the conditions under which insured the car. Almost all insurance companies guarantee Hull + CTP, but often in small print at the end refers to the unconditional franchise – sum, which the driver runs the risk of accidents. And some companies provide a franchise agreement, even under the action of CTP, ie, when the driver of the rental car in an accident is to blame. If you are going to far trip, you should pay attention to the limits on mileage, in case of exceeding the limit will have to pay.

Largest Manufacturer Suspensions Axles

admin

BPW – the largest manufacturer of suspension, axles for trailers, semitrailers, as well as spare parts. Company History BPW History began in 1898. The initial company name was "Bergische Patentachsenfabrik Wiehl". Smithy companies engaged in the production and repair of axles for agricultural machinery and vehicles for various purposes. The parent company, the BPW Viel (Wiehl) Company BPW Bergische Achsen is a leading manufacturer of axles and systems suspensions for trailers in the European market. The company is composed of 13 factories worldwide, employing about 4700 employees. BPW produces over 250 000 axles per year. The production program consists of about 450 different versions of axes. Comparative calculations made by leading European transport companies, show that operating costs for trailers with BPW running gear for its 10 – year operation up to 25% lower than when operating with axles and suspensions of other manufacturers. BPW company is constantly working to modernize and improve its products. Over 400 patents received by engineers and designers BPW, is proof of that. Significant impact on the operating costs of the rolling stock has a line of technical performance to the conditions of its use. Operating conditions trailers in the Russian conditions significantly different from those from Western Europe. This is evidenced by the test data obtained in 1996 – 2000 years when driving a mobile laboratory BPW via Russia. Dynamic stresses of driving on our roads, on average 3 times higher than on the roads of Western Europe. Based on the data processed, the designers have made some improvements BPW in the design of axles and suspensions, to best adapt them for use in heavy traffic conditions in Russia.

US Transport

admin

Transport of America, now more profitable to buy at the moment interested in cars because of decadent economy in the country and the world is diminished. People are afraid to give huge sums of money in awe that remain out of work and money to live. But for those who want to take risks, you need to know that the acquisition will be a very profitable machine from America. What are the good qualities of this car? The main plus is the cost. In field rise rate of the euro against the dollar, the difference in the price of the car from Europe and America is increasing day by day. Also, many cars sold in the U.S., adjusted for petrol 92 rooms, while in the fuel tanks Europe poured in most cases, the AI 95. Retro cars from the U.S., are generally better built. The interior will be absolutely automatic transmission, climate control, electronics and lots of different devices. Another plus to everything, America's stores are not prohibited to buy a model or brand of car, not represented in our market. Well, turn on the purchase of new cars are almost always not available. While auto, presented in Russian shops cars, we can expect more than half a car in America you can take right out of the car salona.V same time there is a flip side of it so you need to know. Very often the car is purchased through the photos. At Thus, the client has no guarantee that the defects are limited to those that are visible in the photo. Often, it is not. Immediately after the acquisition of vehicles is a large amount of damage to the body or the internal problems that former owners were not told. There is also some risk of damage to the vehicle during transport, because in order to drive that old car, it is necessary to pass a number of loading and unloading operations. Quite an awkward movement loader to patsarapalas.Nu machine and, of course, that the carriage runs on a very long time. Yet there is a problem of careless attitude people America's cars. This is the budget brand of cars, the owners of which are the lowest strata of society, or used cars as a working loshadi.I so you can understand that it is possible to buy excellent car for a low price in the U.S., if the matter is approached with awe and understanding.

Battery Check

admin

Before you begin to replace the belt, you must remember "route" it passes through the pulleys. Usually "route" is displayed on a special plate, located under the hood. Replacing the belt should performed in accordance with the instructions in the "User's Manual." If not, then it is better to turn to master the service station, it will make you faster and higher quality, as well aware of many features vehicles. You need to make sure that when replacing the belt has been tested and also the state of pulleys and their bearings. If you have the support pulleys play, and you do not remove, it will soon again become a customer service station. Removing backlash takes time, so you can be convinced that "this is nothing," although because of the backlash may suffer a generator or air conditioning. After a short run, check the mutual arrangement of pulleys and state replaced the belt. For this range is applied to a pair of sidewalls pulleys. This way you can identify the pulleys with deviations from linearity, which causes accelerated wear of the belt. With pulleys should not apply too carefully check their energetic enough stagger from side to side. Sometimes in this way can reveal not only the play bearing assembly, but also a crack in the flange or the weakening of fasteners. Rotating pulley enough quickly loosens the attachment and leads to cracks in the flange. Thus, the sequence for replacing the belt: Unplug the 'weight' of the battery. Disconnect all the pipes, remove all the belts, which can interfere with the cover renting a belt drive and work.

Battery Check

admin

Before you begin to replace the belt, you must remember "route" it passes through the pulleys. Usually "route" is displayed on a special plate, located under the hood. Replacing the belt should performed in accordance with the instructions in the "User's Manual." If not, then it is better to turn to master the service station, it will make you faster and higher quality, as well aware of many features vehicles. You need to make sure that when replacing the belt has been tested and also the state of pulleys and their bearings. If you have the support pulleys play, and you do not remove, it will soon again become a customer service station. Removing backlash takes time, so you can be convinced that "this is nothing," although because of the backlash may suffer a generator or air conditioning. After a short run, check the mutual arrangement of pulleys and state replaced the belt. For this range is applied to a pair of sidewalls pulleys. This way you can identify the pulleys with deviations from linearity, which causes accelerated wear of the belt. With pulleys should not apply too carefully check their energetic enough stagger from side to side. Sometimes in this way can reveal not only the play bearing assembly, but also a crack in the flange or the weakening of fasteners. Rotating pulley enough quickly loosens the attachment and leads to cracks in the flange. Thus, the sequence for replacing the belt: Unplug the 'weight' of the battery. Disconnect all the pipes, remove all the belts, which can interfere with the cover renting a belt drive and work.

Battery Check

admin

Before you begin to replace the belt, you must remember "route" it passes through the pulleys. Usually "route" is displayed on a special plate, located under the hood. Replacing the belt should performed in accordance with the instructions in the "User's Manual." If not, then it is better to turn to master the service station, it will make you faster and higher quality, as well aware of many features vehicles. You need to make sure that when replacing the belt has been tested and also the state of pulleys and their bearings. If you have the support pulleys play, and you do not remove, it will soon again become a customer service station. Removing backlash takes time, so you can be convinced that "this is nothing," although because of the backlash may suffer a generator or air conditioning. After a short run, check the mutual arrangement of pulleys and state replaced the belt. For this range is applied to a pair of sidewalls pulleys. This way you can identify the pulleys with deviations from linearity, which causes accelerated wear of the belt. With pulleys should not apply too carefully check their energetic enough stagger from side to side. Sometimes in this way can reveal not only the play bearing assembly, but also a crack in the flange or the weakening of fasteners. Rotating pulley enough quickly loosens the attachment and leads to cracks in the flange. Thus, the sequence for replacing the belt: Unplug the 'weight' of the battery. Disconnect all the pipes, remove all the belts, which can interfere with the cover renting a belt drive and work.

First Jacks

admin

Another bad point – the low stability of the jack. To use it absolutely necessary wheel stops, and the car must stand at the highest level surface. Besides, the surface must be very hard otherwise the slightest misalignment install jack puts himself on one side, then prodavlivaya on what it's worth bearing faces. In Overall rombovye jacks firmly taken its place in the car trunk. Perhaps this is the most suitable option for small hoist repair and replacement of wheels on the right on the road. The next type jacks – rack. At the core of such a device – a vertical bar with teeth or holes. Pick-up rack and pinion jack is moved in a vertical plane or with the rocker arm or a rotating toothed gear – then instead of a lever with a jack handle rotation. Rack and pinion jacks have been applied mainly to commercial vehicles. There are several reasons – first of all a big load capacity and stroke. Not least occupies a high efficiency unit, which reaches 85%. However, the design of ram rack has some drawbacks, the most significant of which is the size of the ram – in the trunk of a passenger car he will be manifestly closely. So, we examined the main types of jacks, their pros and cons. We now turn from theory to practice. How to choose the jack and how to use it? Here are answers to frequently asked questions. Q: What kind of jack to choose as shipped with a? A: First you should look in the trunk and spare tire niche – jack there are probably already there and it should be sufficient for all possible types of road repairs.

First Jacks

admin

Another bad point – the low stability of the jack. To use it absolutely necessary wheel stops, and the car must stand at the highest level surface. Besides, the surface must be very hard otherwise the slightest misalignment install jack puts himself on one side, then prodavlivaya on what it's worth bearing faces. In Overall rombovye jacks firmly taken its place in the car trunk. Perhaps this is the most suitable option for small hoist repair and replacement of wheels on the right on the road. The next type jacks – rack. At the core of such a device – a vertical bar with teeth or holes. Pick-up rack and pinion jack is moved in a vertical plane or with the rocker arm or a rotating toothed gear – then instead of a lever with a jack handle rotation. Rack and pinion jacks have been applied mainly to commercial vehicles. There are several reasons – first of all a big load capacity and stroke. Not least occupies a high efficiency unit, which reaches 85%. However, the design of ram rack has some drawbacks, the most significant of which is the size of the ram – in the trunk of a passenger car he will be manifestly closely. So, we examined the main types of jacks, their pros and cons. We now turn from theory to practice. How to choose the jack and how to use it? Here are answers to frequently asked questions. Q: What kind of jack to choose as shipped with a? A: First you should look in the trunk and spare tire niche – jack there are probably already there and it should be sufficient for all possible types of road repairs.

First Jacks

admin

Another bad point – the low stability of the jack. To use it absolutely necessary wheel stops, and the car must stand at the highest level surface. Besides, the surface must be very hard otherwise the slightest misalignment install jack puts himself on one side, then prodavlivaya on what it's worth bearing faces. In Overall rombovye jacks firmly taken its place in the car trunk. Perhaps this is the most suitable option for small hoist repair and replacement of wheels on the right on the road. The next type jacks – rack. At the core of such a device – a vertical bar with teeth or holes. Pick-up rack and pinion jack is moved in a vertical plane or with the rocker arm or a rotating toothed gear – then instead of a lever with a jack handle rotation. Rack and pinion jacks have been applied mainly to commercial vehicles. There are several reasons – first of all a big load capacity and stroke. Not least occupies a high efficiency unit, which reaches 85%. However, the design of ram rack has some drawbacks, the most significant of which is the size of the ram – in the trunk of a passenger car he will be manifestly closely. So, we examined the main types of jacks, their pros and cons. We now turn from theory to practice. How to choose the jack and how to use it? Here are answers to frequently asked questions. Q: What kind of jack to choose as shipped with a? A: First you should look in the trunk and spare tire niche – jack there are probably already there and it should be sufficient for all possible types of road repairs.